Metcal MX-5210 Soldering and Rework System
The MX-5210 offers users an ergonomic hand-piece for soldering and rework with hundreds of tip geometries to address the widest range of applications.
NOTE: METCAL System comes without tips and those have to be purchased separately!
Brand | Metcal |
---|
MX-5210 Soldering and Rework System
The MX-5210 is configured with the Metcal Advanced™ Hand-piece. This system is highly effective for soldering applications including: lead-free, high mass components or boards, thermally sensitive components requiring low operating temperature, high volume production soldering and touch-up soldering operations. For these applications, STTC Series soldering cartridges are offered in dozens of geometries and sizes.
In addition, the MX-5200 can be used for conduction rework of SMDs when using SMTC Series soldering cartridges with such geometries as: blade, tunnel and quad styles that provide exact part fit up. Even more, the high power MX-5200 System is ideally suited for quickly and efficiently heating high-mass tips in this range, increasing operator throughput. A variety of SMTC soldering cartridge geometries are available.
MX-5200 ADVANCED FEATURES
Ambient Operating Temperature:
10- 40°C (50°F - 104°F)
Maximum Enclosure Temperature:
55°C (131°F)
Input Line Voltage:
100- 240 VAC, grounded circuit
Input Line Frequency:
50/60 Hz
Power Consumption:
125 Watts
Output Power Maximum:
80 Watts max. Per channel at 22°C
Output Frequency:
13.56 MHzC
Power Cord 3-Wire:
183cm (18/3") SJT
Dimensions w x d x h:
12.1cm x 13.0cm x 23.5cm
(4.8" x 5.1" x 9.3")
Certification / Marking:
cTUVus, CE
Tip-to-Ground Potential:
< 2mV
Tip-to-Ground Resistance:
< 2 ohms
Idle Temperature Stability:
± 1.1°C (2°F) in still air
Hand-piece Cable Length:
L=122cm (48"), burn resistant, ESD safe
Hand-piece Connector:
F connector
Workstand Dimensions w x dx h:
8.6cm x 19.1cm x 8.3cm (3.4" x 7.5" x 3.3")
Weight of the power supply:
7.4 lbs (3.35 kg)
Weight of the workstand:
1.05 lbs (.476 kg
MX-5000 SERIES SOLDERING SYSTEMS
The new MX-5000 Series Soldering and Rework System is the next generation of the trusted Metcal Soldering Systems that will enable you to increase productivity and process control for a wide range of applications with these new features:
More power. With nearly double the power of its predecessor, the MX-5000 time to recovery increases production rates and throughput.
Improved ergonomics. A new Metcal Advanced™ Hand-piece for soldering and rework is carefully designed to decrease operator fatigue and enhance the operator manual dexterity resulting in productivity gains.
Greater process control. SmartHeat® Technology in every MX-5000 means that soldering and rework are always performed at safe, controlled temperatures. Metcal users know that moderate fixed temperatures, where power is varied, provide the best assurance for a well controlled soldering and rework process.
Metcal Gives You Choices
The new MX-5000 Series provides users with a wide range of choices to address conduction soldering and rework processes. At the core of each system is a microprocessor controlled power supply that provides more power, the highest level of precision and advanced user features for greater process control.
Power Supply: Process Feedback and Power
The MX-5000 has a built-in power indication meter with digital display and bar graph that dynamically provides the operator with feedback on the status of the soldering operation. Whether using a large mass rework tip for QFPs or a fine-point soldering tip, the power indication meter is a valuable resource for making consistent, acceptable solder joints.
The system has four mode indications: "Ready Mode": the hand-piece is removed from the workstand, ready for soldering or rework. "Power Mode": the hand-piece's tip is in contact with the load. The power indication meter provides graphical and numeric feedback on the system power output. "Sleep Mode": the hand-piece is at rest in the workstand; power is reduced to the hand-piece. "Powersave Mode": power to the hand-piece is shut off. This programmable feature allows a supervisor to set the desired time to cut off power to the hand-piece.
Brand | Metcal |
---|